Skip to main content
Top TechHardware
Collections
Send a correction

PC parts and peripherals

7 Best PC Fan Hubs and Hardware Fan Controllers in 2026

The Corsair iCUE LINK System Hub is the top pick for most new builds because it drives a whole chain of fans and accessories over a single cable and one hub port set. Buyers who want simple PWM splitting without software should look at the ARCTIC Case Fan Hub. For builds that need per-channel control and temperature sensing, the NZXT RGB & Fan Controller is the better fit.

By · Published 22 Nov 2026

7 products compared

We run no ads and no affiliate links at launch. The order of a list follows our published method. How lists are ordered: how we score.

Prices are the starting prices vendors list publicly. Plans change, so confirm the current price on the vendor page before you buy.

Key takeaways

  • Hubs split one motherboard header into many fan connections; controllers add software or knob-based control.
  • The ARCTIC Case Fan Hub powers up to 10 fans from one SATA connection and needs no software.
  • Corsair iCUE LINK moves fan power and data over one cable per chain, cutting cable clutter.
  • Check the hub's total current rating against your fan count before buying.
  • Most hubs cost between about $15 and $60; premium controllers sit higher.

Side-by-side

Grouped by fit and cost. Tap a product to jump to its full entry.

FitCost
ProductBest forStandout featureListed starting priceFree plan or trial
1Corsair iCUE LINK System HubCable-light builds with iCUE LINK fansOne cable per fan chain carries power and dataCheck current retail priceOne-time hardware purchase
2ARCTIC Case Fan HubCheap, software-free fan splittingPowers up to 10 fans from one SATA plugSee vendor siteOne-time hardware purchase
3NZXT RGB & Fan ControllerPer-channel fan and RGB controlSeparate fan and RGB channelsCheck current retail priceOne-time hardware purchase
4Lian Li UNI HUB SL V2Lian Li SL and AL fan buildsDesigned for Lian Li UNI fan daisy chainsSee vendor siteOne-time hardware purchase
5Cooler Master MasterFan ARGB and PWM HubBudget ARGB plus PWM splittingHandles both PWM fans and ARGB lightingSee vendor siteOne-time hardware purchase
6Thermalright Fan HubLow-cost PWM splittingVery cheapSee vendor siteOne-time hardware purchase
7Aquacomputer OCTOAdvanced multi-channel controlMultiple fan channels with software controlSee vendor siteOne-time hardware purchase

How we picked

This guide is based on research, not lab testing. We read vendor product pages, spec sheets and manuals for each hub and controller, then compared channel counts, power connections, software support and published prices. We favoured models released or refreshed in the 2023 to 2025 window that the manufacturer still lists as current. Where a vendor does not publish a firm price, we say so rather than guess. No hands-on benchmarks or measurements are claimed here.

The 7 picks in detail

#2

ARCTIC Case Fan Hub

Official site
Screenshot of the ARCTIC Case Fan Hub website
Vendor homepage, Nov 2026. Source: arctic.de
Best for
Cheap, software-free fan splitting
Standout
Powers up to 10 fans from one SATA plug
Starting price
See vendor site
Free plan or trial
One-time hardware purchase

The ARCTIC Case Fan Hub is a simple splitter board. One PWM signal from the motherboard controls every connected fan, and a SATA power connector feeds the fans so they do not draw current from the board header. ARCTIC lists support for up to 10 fans. It is the cheapest way to run a large case fan array from a single header.

Because all fans share one control signal, it suits builds where fans are the same model and can run at the same speed. It does not report individual fan speeds, and it has no RGB handling. For a budget air-cooled build with many case fans, it is the practical choice. Check the vendor site for the current price.

Where the price comes from

See vendor site. Hardware prices move often, so check the ARCTIC Case Fan Hub maker page or a retailer before you buy.

Benefits

  • Powers up to 10 fans from one SATA plug
  • no software needed
  • very low cost

Drawbacks

  • No per-fan control
  • all fans follow one PWM signal

Use case to skip: this limit matters to you: no per-fan control.

Our take. A sensible pick for cheap, software-free fan splitting.

If it does not fit, compare Corsair iCUE LINK System Hub or NZXT RGB & Fan Controller in this list.

#3

NZXT RGB & Fan Controller

Official site
Screenshot of the NZXT RGB & Fan Controller website
Vendor homepage, Nov 2026. Source: nzxt.com
Best for
Per-channel fan and RGB control
Standout
Separate fan and RGB channels
Starting price
Check current retail price
Free plan or trial
One-time hardware purchase

This controller gives you individual channels for fans and for RGB lighting, managed through NZXT CAM. It connects internally by USB and SATA power. NZXT lists it as supporting multiple fan channels and separate RGB channels, so you can set different curves per group rather than one signal for everything.

It suits builds that want software curves and lighting control without buying a full ecosystem of fans. The catch is that setup and tuning depend on CAM, and the channel count is smaller than a large passive hub. Check the vendor page for the exact channel ratings before you plan a big fan array.

Where the price comes from

Check current retail price. Hardware prices move often, so check the NZXT RGB & Fan Controller maker page or a retailer before you buy.

Benefits

  • Separate fan and RGB channels
  • works with NZXT CAM software
  • supports temperature-based curves

Drawbacks

  • Best features need CAM installed
  • channel count is limited

Use case to skip: this limit matters to you: best features need CAM installed.

Our take. A sensible pick for per-channel fan and RGB control.

If it does not fit, compare Corsair iCUE LINK System Hub or ARCTIC Case Fan Hub in this list.

#4

Lian Li UNI HUB SL V2

Official site
Screenshot of the Lian Li UNI HUB SL V2 website
Vendor homepage, Nov 2026. Source: lian-li.com
Best for
Lian Li SL and AL fan builds
Standout
Designed for Lian Li UNI fan daisy chains
Starting price
See vendor site
Free plan or trial
One-time hardware purchase

The UNI HUB is the controller for Lian Li's UNI fan line, where fans clip together and share one cable per group. The hub links those groups to the motherboard and to power, and Lian Li's L-Connect software handles speed and lighting. It is the natural companion if you are already buying SL or AL series fans.

It is not a universal hub. If your fans are from another brand, this is the wrong part. For a Lian Li build, though, it removes most of the wiring and centralises control. Check the vendor site for the current hub price and which fan series it supports.

Where the price comes from

See vendor site. Hardware prices move often, so check the Lian Li UNI HUB SL V2 maker page or a retailer before you buy.

Benefits

  • Designed for Lian Li UNI fan daisy chains
  • reduces cable count
  • works with L-Connect software

Drawbacks

  • Tied to Lian Li fan families
  • not a general splitter

Use case to skip: this limit matters to you: tied to Lian Li fan families.

Our take. A sensible pick for lian Li SL and AL fan builds.

If it does not fit, compare Corsair iCUE LINK System Hub or ARCTIC Case Fan Hub in this list.

#5

Cooler Master MasterFan ARGB and PWM Hub

Official site
Screenshot of the Cooler Master MasterFan ARGB and PWM Hub website
Vendor homepage, Nov 2026. Source: coolermaster.com
Best for
Budget ARGB plus PWM splitting
Standout
Handles both PWM fans and ARGB lighting
Starting price
See vendor site
Free plan or trial
One-time hardware purchase

This hub splits both fan power and addressable RGB from one board. It is SATA powered and aimed at budget builds that want a tidy ARGB setup without a full controller. Cooler Master lists it as part of the MasterFan accessory line.

Because control is shared, all connected fans and lights follow the same signal. That is fine for matching fans but not for per-fan curves. It suits first-time builders who want fewer cables and a single lighting zone. Check the vendor page for the supported fan and LED counts before buying.

Where the price comes from

See vendor site. Hardware prices move often, so check the Cooler Master MasterFan ARGB and PWM Hub maker page or a retailer before you buy.

Benefits

  • Handles both PWM fans and ARGB lighting
  • SATA powered
  • simple button or board control

Drawbacks

  • Shared control across connected fans
  • limited documentation on limits

Use case to skip: this limit matters to you: shared control across connected fans.

Our take. A sensible pick for budget ARGB plus PWM splitting.

If it does not fit, compare Corsair iCUE LINK System Hub or ARCTIC Case Fan Hub in this list.

#6

Thermalright Fan Hub

Official site
Screenshot of the Thermalright Fan Hub website
Vendor homepage, Nov 2026. Source: thermalright.com
Best for
Low-cost PWM splitting
Standout
Very cheap
Starting price
See vendor site
Free plan or trial
One-time hardware purchase

Thermalright's fan hub is a plain PWM splitter. It takes one signal from the board and feeds several fans, with SATA power for the load. It is one of the lowest-cost ways to run multiple case fans from a single header, and it pairs well with Thermalright's own budget fan lines.

There is no software, no lighting control and no per-fan reporting. It suits budget builds and anyone who just needs more fan headers. Check the vendor site for the number of ports and the total current rating, since those figures matter more than the price on a part this simple.

Where the price comes from

See vendor site. Hardware prices move often, so check the Thermalright Fan Hub maker page or a retailer before you buy.

Benefits

  • Very cheap
  • simple PWM splitting
  • SATA powered

Drawbacks

  • No software or RGB control
  • basic build quality

Use case to skip: this limit matters to you: no software or RGB control.

Our take. A sensible pick for low-cost PWM splitting.

If it does not fit, compare Corsair iCUE LINK System Hub or ARCTIC Case Fan Hub in this list.

#7

Aquacomputer OCTO

Official site
Screenshot of the Aquacomputer OCTO website
Vendor homepage, Nov 2026. Source: aquacomputer.de
Best for
Advanced multi-channel control
Standout
Multiple fan channels with software control
Starting price
See vendor site
Free plan or trial
One-time hardware purchase

The Aquacomputer OCTO is a fan controller aimed at custom water-cooling and advanced builds. It offers several fan channels plus inputs for temperature sensors, and it is configured through Aquacomputer's software. It can drive pumps and fans from the same device, which is why loop builders use it.

It costs more than a simple splitter and takes more setup time. For a standard air-cooled build, it is overkill. For a loop with several sensors and a pump, it replaces a pile of splitters with one controlled device. Check the vendor site for channel ratings and sensor support.

Where the price comes from

See vendor site. Hardware prices move often, so check the Aquacomputer OCTO maker page or a retailer before you buy.

Benefits

  • Multiple fan channels with software control
  • supports temperature sensors and flow meters
  • strong for custom loops

Drawbacks

  • Higher cost
  • setup is more involved

Use case to skip: this limit matters to you: higher cost.

Our take. A sensible pick for advanced multi-channel control.

If it does not fit, compare Corsair iCUE LINK System Hub or ARCTIC Case Fan Hub in this list.

What specs matter when you buy

Start with channel count and total current. A hub's job is to move power safely, so the vendor's total amp or watt rating matters more than the number of ports. Add up your fans' rated current and leave headroom. If the hub is SATA powered, the fans draw from the power supply, not the motherboard header, which is safer for large arrays.

Next, decide between shared and per-channel control. A passive splitter sends one PWM signal to every fan, so all fans run at the same speed. A controller with separate channels lets you set different curves for intake, exhaust and CPU groups. If your fans are identical and you tune by ear, a splitter is enough. If you want quiet idle and strong load cooling, per-channel control helps.

Then check the ecosystem. Corsair iCUE LINK, Lian Li UNI and NZXT CAM each work best with their own fans and software. Mixing brands through a hub usually means losing lighting control or per-fan reporting. Also confirm the connection type: most hubs need a USB header and SATA or PCIe power, and small boards may not have a free USB header. Finally, check warranty length and whether the vendor publishes a clear spec sheet, since that is the sign of a part you can plan around.

Questions worth answering first

Buying checklist

  • Count your fans and add up their rated current, then compare with the hub's total rating.
  • Confirm the hub is SATA or PCIe powered if you plan to run many fans.
  • Check that your motherboard has a free USB header if the controller needs one.
  • Decide whether you need per-channel control or one shared PWM signal is enough.
  • Confirm the hub supports your fan brand's connectors and lighting standard.
  • Read the vendor spec sheet for port count, warranty and software requirements.

FAQ

Do I need a fan hub if my motherboard has enough headers?

Not always. If your board has enough headers and the total fan current is within the header rating, you can skip a hub. A hub helps when you have more fans than headers, when you want one cable run, or when fan current would exceed a single header's safe limit.

Can I mix fan brands on one hub?

Usually yes for power and PWM speed, but lighting control often breaks. Addressable RGB standards differ between brands, and software from one vendor will not control another brand's lights. For lighting, keep fans within one ecosystem or use a hub that supports the standard your fans use.

What is the difference between a hub and a controller?

A hub splits one signal to many fans. A controller adds logic: separate channels, software curves, temperature inputs or lighting effects. Hubs are cheaper and simpler. Controllers cost more but give finer control, which matters for quiet builds and custom loops.

How many fans can one hub run?

It depends on the hub's total current rating, not just its port count. Vendors publish a total amp or watt figure. Add up your fans' rated current and stay below that number with some headroom. A hub with many ports can still be overloaded by high-current fans.

Do fan hubs need software?

Passive hubs do not. They follow the motherboard's PWM signal. Controllers usually need vendor software for curves and lighting, and some need a USB connection. If you want a set-and-forget build, a passive SATA-powered hub is the simplest option.

Are expensive controllers worth it for a normal build?

For a standard air-cooled PC, a cheap hub is usually enough. Expensive controllers make sense for custom water loops, multi-sensor setups or builds where per-channel curves and lighting matter. Match the part to the build rather than buying the top model by default.

Sources we checked

  1. Corsair iCUE LINK System Hub (official site)
  2. ARCTIC Case Fan Hub (official site)
  3. NZXT RGB & Fan Controller (official site)
  4. Lian Li UNI HUB SL V2 (official site)
  5. Cooler Master MasterFan ARGB and PWM Hub (official site)
  6. Thermalright Fan Hub (official site)
  7. Aquacomputer OCTO (official site)

Change log: First published 22 Nov 2026.

Keep reading